Operation Instruction
Welcome to our company, it’s our honor you can use our
laser sight products！
Before using this
product,please take some time review the Operation Instruction carefully,it
shows the correct operation manners and maintaince instructions in order to
improve the product function and service life.
Model: 2HY01G 2HY01R 2HY01I
Laser wave
length 532nm
635-660nm 830-850nm
Laser Power＜5mw
Laser
working temp: -20°C——+50°C
Laser Shooting Distance:（at night）500-2000
Meters
Laser Spot 25-35mm@50m
LED Lighting Power: 180 Lumen
LED Lighting Visibility: 130 Meters
Battery CR2 (1pcs)
Working Votage: 3V-8.2V
Continuous single laser lighting time 9Hours
Continuous single LED lighting time 120Minutes
Continuous Couple(LED+Laser) lighting
time: 90Minutes
Guide Rail Type: International
Standard Rail & Screw and fastener
2>、Product Dimensions Indication：
3>、Product Installation Indication:
1.Battery Fixture：Twist out the battery cap and fill the CR2 battery into battery
house(positive outside,negative inside),and screw up the battery cap is OK.（As Shown In Figure）
2.Installation To
Gun:
4>、Switch Control Indication:
There
are three Switching Gears in this product, Main Switches are located on both
two sides, press any of the two can get laser started. Toggle Switch is located
in the back,when poking to the left,it shows both LED and Laser; when poking to
the middle,it shows Single Laser; When pocking the the right,it shows Single
Led(again press any of the switches on both two sides it shows the strobe mode)
|
Ballistic adjust up and down
|
|
About ballistic adjusting
|
|
This is a main switch on both
sides of the switch
|
|
Gear switch
|
5>、Product Maintain and Warning：
1．Sliding Block Maintaince: Frequently check if there is foreign matter
else existed inside the dovetail slot,prevent loose between dovetail and gun.
2. When there is foreign matter existed on the laser mouth or Led mouth,it
should be cleaned with a cotton stick,sharp or harden object is forbidden.
Warning:
FAILURE TO FOLLOW ANY OF THE FOLLOWING WARNINGS MAY
RESULT IN SEVERE INJURY OR DEATH TO YOU OR OTHERS.
Prior to installing LASERWIN products, ensure that the firearm is unloaded, the magazine is removed, safety on and finger(s) off the trigger.
DO NOT install or use LASERWIN product if the installation of the product affects the safe function of the firearm. If, while installing LASERWIN products, you have any trouble with the fit or functionality of the firearm, STOP IMMEDIATELY .
ALWAYS FOLLOW THE 4 RULES OF FIREARM SAFETY:
1. Handle all firearms as if they are loaded.
2. Never let the muzzle cover anything that you are not willing to destroy.
3. Keep your finger off the trigger until your sights are on the target and you are ready to fire.
4. Be sure of your target and what is beyond.
Remember, the user is ALWAYS responsible for the safe use of a firearm.
Crimson Trace recommends that every gun owner take a gun safety course from a certified NRA Instructor
before handling or firing your firearm.
INSTALLATION INSTRUCTIONS
1. Make sure firearm is unloaded. Remove magazine and double check that chamber is empty.
2. Install CR2 battery into the light side of the Lightguard, positive (+) side facing up (toward gun side).
3. Install the light side (right half) of the Lightguard onto the trigger guard and snap into place.
4. Insert locking groves of left side into the right at an angle. Apply pressure until both sides join together.
5. Install the two CTC provided screws into the left side (non-laser side) of the Lightguard using the .050"
hex wrench (provided). Tighten, drawing two halves together, until there is no gap. Use care to avoid
over-tightening as this may cause damage to the Lightguard.
6. To activate Lightguard, slide the master ON/OFF switch upward to the ON position. The switch is located
below the light aperture. Press pressure activation pad located in center of front strap directly beneath
trigger guard to activate the light.
BATTERY GUIDELINES & REPLACEMENT
Our batteries provide two hours of light illumination under normal conditions. Keep battery compartment
free of dirt or other contaminants. Debris inside the battery compartment may affect light operation and
performance. Lightguard models use one (1) CR2 lithium battery.
To replace batteries:
1. Ensure that your firearm is unloaded.
2. Check again.
3. Remove Lightguard and old battery.
4. Install new battery in accordance to installation instructions.
FAILURE TO FOLLOW ANY OF THE FOLLOWING WARNINGS MAY
RESULT IN SEVERE INJURY OR DEATH TO YOU OR OTHERS.
Screws
Battery
Locking
Grooves
Master On/Off Switch
没有评论:
发表评论